Over 20 years of plumbing has shown Norbert that a failing shower or bath in Maidstone usually needs less replacing than people fear. Vision Plumbing is one plumber who quotes your bath and shower repair, turns up and does it.
The Quick Answer
- Why a lukewarm bath can point to the immersion heater, not the taps
- Seven common shower and bath faults and the part behind each
- The four-step order of work from isolation to reseal and test
- Which electric shower parts are repaired and which mean a new unit
- When a corroded valve or a cracked bath gets replaced outright
Vision Plumbing is a sole trader plumbing, drainage and hot water business: the man who reads your shower fault is the man who fixes it and stands behind the one year warranty on parts and labour, and he handles hot water cylinder repair in Maidstone too.
Get a quick quote from Vision Plumbing in Maidstone today and find out whether your shower or bath needs a part or a replacement.

The Fitting or the Hot Water Behind It
Most bath and shower faults in Maidstone start in one of two places: the fitting itself, or the hot water feeding it. We separate the two before anything gets unscrewed. A mixer shower or a bath tap draws its hot water from a cylinder. In many homes that cylinder is heated by an immersion heater running on the standard electrical supply, sometimes on off-peak.
So if the bath runs lukewarm from both taps, the taps are rarely the problem. The element or its thermostat usually is. Immersion heater repair and replacement has its own page. This page stays with the fittings: the shower, the valve, the pump, the tray, the bath, its taps and its waste.
That first check matters. It stops you paying for a new shower valve when the fault sits in the airing cupboard.
Get a quick quote from Vision Plumbing for bath and shower repair in Maidstone, from a worn thermostatic cartridge to a cracked bath swapped out.

Common Water Heater Problems for Maidstone Homes
The faults we see at a shower or a bath follow a short list. Each has a different cause, and the cause decides whether it is a repair or a swap.
- Shower runs hot then cold: a worn thermostatic cartridge, or a mixer valve with scale inside it.
- Weak flow from a mixer: a blocked flow regulator or showerhead, low pressure on the hot side, or a pump that has lost its push.
- Electric shower cutting out: the thermal cut-out tripping, often from scale on the heating element or a failing pressure switch.
- Noisy or pulsing pump: air in the supply, worn bearings or a failing impeller.
- Water below the tray or bath: a failed silicone seal, a loose waste or overflow, or a cracked tray.
- Dripping bath tap: a perished washer or a worn ceramic cartridge.
- Bath draining slowly: hair and soap packed into the waste trap.
Most of these are parts. A cartridge, a seal, a washer. Naming the fault properly means you pay for the part that failed and nothing beside it.

Installation and Repair Process in Maidstone
A bath and shower repair in Maidstone and water leak detection in Maidstone sit inside the same area we cover, and sometimes inside the same visit. The order of work never changes.
1. Isolate and test
We isolate the water to the fitting, and the electrical supply where there is an electric shower or a pump. Then we test what is actually wrong: temperature at the outlet, flow rate, and whether the hot supply is reaching the fitting at all.
2. Find the source of any leak
A stain on the ceiling below a bathroom is not always the tray. It can be the waste, the seal, or a pipe hidden in the wall. Where the source is out of sight, thermal imaging and acoustic tracing find it before a floor comes up.
3. Repair or replace the part
Cartridge, washer, seal, pump, waste. The failed part comes out and the matching part goes in. If the fitting is past repair, you hear why before anything is swapped.
4. Reseal and run
Old silicone is cut out completely, the joint cleaned and dried. A bath is resealed with water in it, so the joint is not stretched the first time somebody climbs in. Then we run the shower and fill the bath to check temperature, flow and every seal under load.

Electric Shower Faults
An electric shower is a tankless water heater. It heats cold mains water as it passes over an element inside the unit, with no cylinder behind it. That makes it the one shower whose temperature fault lives inside the box on the wall.
The parts that fail inside it are known: the heating element, the thermal cut-out, the pressure switch, the flow valve and the solenoid. Scale builds on the element and the cut-out trips. A cracked casing or a burnt terminal block is a different matter. That usually means a new unit.
Electric shower repair here in Maidstone and shower fitting in Royal Tunbridge Wells are the same work, done the same way. The isolator is switched off and the supply proved dead first. Then the cover comes off. Mixer and power showers are a separate case: they take hot water from your cylinder, and their faults sit in the valve or the pump.
Get a quick quote from Vision Plumbing for bath and shower repair in Maidstone, from a worn thermostatic cartridge to a cracked bath swapped out.

Choosing a Qualified Installer
Vision Plumbing is Norbert. One plumber, over 20 years' experience, and no dispatch list between you and the man who looks at your shower.
That has practical consequences on a bath and shower job. The person who diagnosed the thermostatic cartridge is the person who fits it, so nothing is lost between a survey visit and a fitting visit. If the fault turns out to be the immersion heater or the cylinder rather than the valve, the same man tells you so.
- The quote and the work come from the same plumber.
- Every job carries a one year warranty on parts and labour.
- Gas and boiler faults go to a registered gas engineer, never to us.
- Replacing a failed fitting is our work. Refitting a whole bathroom is not.

When a Shower or Bath Is Past Repair
Some fittings are past repair. An electric shower with a burnt terminal block, a scaled element on a model with no parts left, a thermostatic valve whose body has corroded: these get replaced. So does a cracked bath. We swap it out rather than patch it, then reconnect the taps, waste and overflow to the new one.
A replacement electric shower goes onto the existing supply only where the cable and isolator suit the new unit's rating. We check that before quoting, not after. From Maidstone across to Sevenoaks, it is the same plumber handling a failed shower swapped out here and shower installation in Sevenoaks.
Tell us what the shower or the bath is doing. We will tell you whether it needs a part or a replacement, and why. Get a quick quote.
Get a quick quote from Vision Plumbing for bath and shower repair in Maidstone, from a worn thermostatic cartridge to a cracked bath swapped out.
Common Questions About Bath And Shower Repair in Maidstone
Is Maidstone inside the area you cover for bath and shower repairs?
Yes. We cover Sevenoaks and the towns around it across Kent, Medway, Surrey, East Sussex, West Sussex and south-east London, and Maidstone sits well inside that. The plumber who quotes your shower or bath job in Maidstone is the plumber who turns up and does it. Get a quick quote and describe the fault.
How much does a bath or shower repair in Maidstone cost?
It depends on the fault. A worn tap washer and a corroded thermostatic valve are very different jobs, so we do not give a figure before knowing which one you have. Tell us what the fitting is doing and the quote follows that conversation. Every job carries a one year warranty on parts and labour.
Can a cracked bath be repaired?
We replace it. A crack in a bath is not something we patch or resurface. We take the cracked bath out, fit the replacement, reconnect the taps, waste and overflow, and reseal it with water in the bath so the joint holds. A leak around a sound bath is different: usually a seal or a waste, and repairable.



